Electric Vehicles
Filter by brand
- 142
- 1
- 2
Showing 129–144 of 145 results
AiM EPM Power Distribution Interface
$1.282,46 + VAT ($1.538,95)• This item is a Pre-Order Item Expected in Late 2022!
• Easy Replacement of Traditional Fuse and Relay Systems.
• Housed in an anodised billet Aluminium case
• Designed to be used with current Aim Dashes
AiM ECU Bridge for Porsche 996-997 GT3 CUP
$444,42 + VAT ($533,30)• ECU Bridge is to be used when the Engine Control Unit transmits data by either OBDII, CAN or RS232.
• Aim has developed hundreds of different protocols to make compatibility with virtually
• Aim SmartyCam HD and Aim SmartyCam GP HD racing cameras.
AiM ECU Bridge for Ferrari F430 Challenger GT3
$444,42 + VAT ($533,30)• ECU Bridge is to be used when the Engine Control Unit transmits data by either OBDII, CAN or RS232.
• ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ecus on the other side.
• RPM data can be obtained with connection to the coil or by reading a square wave signal generated by the ignition system.
AiM Dual Brake Pressure Mounting T-Piece Kit
$121,90 + VAT ($146,28)• Suitable for M10 brake pressure sensors
• Dual pressure T-piece
AiM DTA S60
$114,28 + VAT ($137,14)• Aim Looms, Cables, Connectors and Harnesses are highly engineered to withstand the intense rigours of the Motorsport environment
• User-friendly systems which allow you to easily connect your ECU to our high tech data logger.
AiM Draw Wire Position Sensor Pot 750mm
$520,60 + VAT ($624,72)• Measure displacement & position
• Linearity – +0.375mm
• Robust housing
• 4 pin plastic binder connector
AiM Data Hub 2 CAN connection multiplier 150 cm cable With External Power Lead
$95,23 + VAT ($114,28)• Five pins 712 male Binder
• Two flying cables
• Two-way hub
• Build a network
AiM CAN Connection Channel multiplier
$330,14 + VAT ($396,17)• Configurable up to 50Hz per channel
• Enhance your logger performance
• Simplify your wiring
• 5 pin Binder 712 male connector
AiM ABS Honeywell – Hall Speed Pick up 719 30CM
$146,02 + VAT ($175,22)• Hall effect wheel speed sensor
• 4 pin 719 binder connector
AiM 6″ TFT Dash Display with Road Icons for PDM08/PDM32
$438,07 + VAT ($525,68)• Check out the Downloads Tab for all the information required on connection and programming to the PDM08 and the PDM32.
• The 6″ dash display is ONLY for use with AiM PDM kits and can not be used as a stand-alone dash display.
• The dashes also double up as a reversing mirror using a separately available camera
• Five status information LEDs
AiM 6″ TFT Dash Display with Race Icons for PDM08/PDM32
$438,07 + VAT ($525,68)• The 6″ dash display is ONLY for use with AiM PDM kits and can not be used as a stand-alone dash display.
• Suitable for replacing all of the dashboard gauges and warning lamps
• Ideal for cars with limited rear vision
AiM 37 Pin Motorcycle Deutsch Harness MXS, MXP, MXG, MXL2, MXM
$488,86 + VAT ($586,63)• Also available is our 37 pins Deutsch harness with a thermocouple connector.
• Analogue sensor channels (sensors) 1, 2, 3, 4
• Optical lap timing sensor output
• Can be used to replace a damaged harness or for a second vehicle installation when sharing a dash logger.
AiM 37 Pin Connector and Pins MXS, MXP, MXG, MXL2 Female Deutsch Connector
$171,42 + VAT ($205,70)• Suitable for MX Series, MXL2
• Ideal for replacement or spares
• 37 pins, One plug
AiM 22 Pin Deutsch Harness MXS, MXP, MXG, MXL2
$419,02 + VAT ($502,82)• Digital wheel speed sensor inputs 2, 3, 4
• Analogue sensor channels 5, 6, 7, 8
• Suitable for MXS, MXP, MXG, MXL2
• Several of the advanced functions rely on this harness
AiM 22 Pin Connector and Pins MXS, MXP, MXG, MXL2 Female Deutsch Connector
$126,98 + VAT ($152,38)• Suitable for MX Series, MXL2
• 22 pins, One plug
• Ideal for replacement or spares
AiM 10″ TFT Dash Display with Road Icons for PDM08/PDM32
$704,72 + VAT ($845,66)• Check out the Downloads Tab for all the information required on connection and programming to the PDM08 and the PDM32.
• The 10″ dash display is ONLY for use with AiM PDM kits and can not be used as a stand-alone dash display.
• Suitable for replacing all of the dashboard gauges and warning lamps
• 10″ TFT dash display
